Mechanical Performance of Rotationally Molded Multilayer mLDPE/Banana-Fiber Composites.

The incorporation of materials different from the polymer within the rotational molding process usually results in lowered mechanical properties, where impact strength is of particular concern. In order to overcome this issue, multilayer structures of virgin polyethylene (PE) and banana fiber composites were prepared to determine the impact of the different layers on the performance of the final part. Cycle time has been studied to identify the influence of the addition of fibers in the process. The tensile, flexural and impact properties have been analyzed, finding improvements in Young's modulus of up to 13%, although at the expense of significant decreases in impact strength. A reduction in the fiber size due to the pulverization process was observed, which affected the rheological and mechanical behavior of the composite. The beneficial effects of working in multiple layers have been demonstrated in this work, where composites with up to 5% of banana fiber have been produced in two-layer structures. Finally, the need to add neat polyethylene in the external layer is also highlighted as a way to counteract the reductions in mechanical properties, particularly for flexural elastic modulus and tensile strength, and this also helps with the drop in impact behavior to a lower extent.

Characterization of PLA Sheets Prepared by Stretching under Different Conditions: Influence of Reprocessing and Establishing Optimal Conditions.

Polylactide (PLA) is one of the most commonly used biomaterials nowadays, with many recognized benefits, particularly in the packaging and single-use products industries. However, little research has been conducted on its stretching behavior. This work investigates the optimal conditions of biaxial stretching of injection-molded PLA samples produced under different processing conditions (pressure, drying, and pre-processing by extrusion, to simulate a recycling step). The injection-molded samples were characterized to determine their mechanical, thermal and thermo-mechanical behavior, water absorption, thermal behavior, and crystallization kinetics. The extruded samples showed reduced thermal stability, lower viscosity, decreased mechanical properties, and higher crystallization rates due to thermal degradation. However, the stretched samples provided similar properties regardless of the materials pre-processing. Regarding the assessment of the biaxial stretching process, processing at lower temperatures provides the films with a higher yield and breaking strength, while the time and strain rates have little influence on such properties. It was then determined that 82 °C is the optimal temperature for stretching the PLA samples. An increase in the stretch ratio provided a higher elastic modulus and higher values of opacity due to an increased crystallinity induced by stress during the process. Films as thin as 50 µm can be obtained by biaxially stretching injection-molded preforms, producing a deformation over 150% and acquiring good mechanical properties: about 90 MPa for the yield and a breaking strength and elastic modulus of 4000 MPa.

Uncertain future for global sea turtle populations in face of sea level rise.

Sea level rise has accelerated during recent decades, exceeding rates recorded during the previous two millennia, and as a result many coastal habitats and species around the globe are being impacted. This situation is expected to worsen due to anthropogenically induced climate change. However, the magnitude and relevance of expected increase in sea level rise (SLR) is uncertain for marine and terrestrial species that are reliant on coastal habitat for foraging, resting or breeding. To address this, we showcase the use of a low-cost approach to assess the impacts of SLR on sea turtles under various Intergovernmental Panel on Climate Change (IPCC) SLR scenarios on different sea turtle nesting rookeries worldwide. The study considers seven sea turtle rookeries with five nesting species, categorized from vulnerable to critically endangered including leatherback turtles (Dermochelys coriacea), loggerhead turtles (Caretta caretta), hawksbill turtles (Eretmochelys imbricata), olive ridley turtles (Lepidochelys olivacea) and green turtles (Chelonia mydas). Our approach combines freely available digital elevation models for continental and remote island beaches across different ocean basins with projections of field data and SLR. Our case study focuses on five of the seven living sea turtle species. Under moderate climate change scenarios, by 2050 it is predicted that at some sea turtle nesting habitats 100% will be flooded, and under an extreme scenario many sea turtle rookeries could vanish. Overall, nesting beaches with low slope and those species nesting at open beaches such as leatherback and loggerheads sea turtles might be the most vulnerable by future SLR scenarios.

Recent Developments in Inorganic Composites in Rotational Molding.

Rotational molding allows for obtaining hollow parts with good aesthetics and properties, having as main drawbacks the lack of pressure and the long cycle times, which limit the range of materials. Different fillers have been introduced in rotomolding to obtain composite materials assessed. This review has shown that glass fibers or particles are the most common material among them, although carbon fibers or clays have also been studied. In general terms, 10% loadings provide an increase in mechanical properties; higher loadings usually lead to a decrease in processability or final properties. When the filler consists of a micro- or nano-material, such as clay or graphene, lower loadings are proposed, generally not exceeding 3%. The use of fillers of an inorganic nature to obtain composites has not been as explored as the incorporation of lignocellulosic materials and even less if referring to waste materials or side streams from industrial processes. So, there is a broad field for assessing the processing and properties of rotomolded composites containing inorganic waste materials, including the study of the relationship between the ratio of filler/reinforcement and the final properties and also their preprocessing (dry blending vs. melting compounding).

Extrinsic traits consistently drive microhabitat decisions of an arboreal snake, independently of sex and personality.

One pivotal topic on habitat selection is to understand the influence of intrinsic and extrinsic factors on the selection process. Although the effect of some extrinsic variables and sex has been extensively studied, almost nothing is known about the effect of personality, particularly on snakes. Here we addressed the relative importance of extrinsic (tree-related) and intrinsic (sex and personality) factors driving microhabitat selection decisions of a nocturnal tree snake (Leptodeira annulata). We implemented a protocol to quantify the influence of personality and sex on the role of extrinsic variables on microhabitat selection. First, we conducted three behavioral experiments to extract the shyness-boldness and avoidance-exploitation personality traits of male snakes. Then, we evaluated the role of sex and personality on the effect of tree-traits (thickness, canopy cover and shelter availability) on microhabitat selection, using two-step conditional logistic regression. Snakes consistently selected tree trunks, preferably thick and with high canopy cover and shelter availability, independently of their sex or personality. For this species, only extrinsic variables determined microhabitat decisions. Our protocol will aid to quantify the role of personality on microhabitat selection of other species and understand whether this is an important variable in habitat decision-making or not.

The role of environmental temperature on movement patterns of giant anteaters.

Mammals can show conspicuous behavioral responses to thermal variation, including changes in movement patterns. We used an integrative approach to understand how environmental temperature can drive the movement behavior of a mammal with low capacity for physiological thermoregulation, the giant anteater (Myrmecophaga tridactyla). We tracked 52 giant anteaters in 7 areas throughout the Brazilian savannah. We estimated the distance moved, area used, use of forest areas, and mean environmental temperature for each monitoring day of each individual. We modeled these data with Mixed Structural Equations - considering the possible interactions between our variables and controlling for sex and body mass. Giant anteaters reduced displacement and increased forest use with decreasing environmental temperature, probably because of their low body heat production. It is possible that they reduce distance moved and area used by reducing the duration of activity. With decreasing temperature, forest habitats become warmer than open ones, besides buffer rain and chilly winds. Reducing displacement and using forests are important strategies to reduce body heat loss and the energetic costs of thermoregulation. However, decreasing movement can limit food access and, consequently, fitness. Therefore, we highlight the importance of forests as thermal shelters. With increasing frequency and intensity of extreme weather events, we showed the need to preserve forest patches to offer suitable conditions for tropical mammals' behavioral thermoregulation. In this context, policies favoring deforestation on Brazilian territory are especially worrisome. Finally, we emphasize the need of integrative approaches to understand the complex interactions between organisms and the environment.

An annual study on plastic accumulation in surface water and sediment cores from the coastline of Tenerife (Canary Island, Spain).

Sediment core samples from high tide lines and in submerged zones as well as surface water samples from eight beaches of Tenerife were analysed. Sampling was conducted over a period of one year in intervals of 5 weeks. The majority of particles were found in the high tide sediment (66%), followed by water samples (23%) and finally in sediment from submerged zones (11%). Regarding the particle amount per volume (items/L), accumulation in sediment samples was statistically higher compared to water samples. Mean values of items/L were higher in high tide sediments. In high tide and water samples, mostly white and transparent particles >1 mm were found. More than 70% were represented by fragments. In sediments from submerged zones, yellow and blue microparticles (<1 mm) were predominant and 61.9% consisted of fibres. Larger particles were mainly identified as PP, PE, PS, PTFE and PVC, while polymer types of smaller particles were more variable.

Sexual, allometric and forest cover effects on giant anteaters' movement ecology.

Knowing the influence of intrinsic and environmental traits on animals' movement is a central interest of ecology and can aid to enhance management decisions. The giant anteater (Myrmecophaga tridactyla) is a vulnerable mammal that presents low capacity for physiological thermoregulation and uses forests as thermal shelters. Here, we aim to provide reliable estimates of giant anteaters' movement patterns and home range size, as well as untangle the role of intrinsic and environmental drivers on their movement. We GPS-tracked 19 giant anteaters in Brazilian savannah. We used a continuous-time movement model to estimate their movement patterns (described by home range crossing time, daily distance moved and directionality), and provide an autocorrelated kernel density estimate of home range size. Then, we used mixed structural equations to integratively model the effects of sex, body mass and proportion of forest cover on movement patterns and home range size, considering the complex net of interactions between these variables. Male giant anteaters presented more intensive space use and larger home range than females with similar body mass, as it is expected in polygynous social mating systems. Males and females increased home range size with increasing body mass, but the allometric scaling of intensity of space use was negative for males and positive for females, indicating different strategies in search for resources. With decreasing proportion of forest cover inside their home ranges, and, consequently, decreasing thermal quality of their habitat, giant anteaters increased home range size, possibly to maximize the chances of accessing thermal shelters. As frequency and intensity of extreme weather events and deforestation are increasing, effective management efforts need to consider the role of forests as an important thermal resource driving spatial requirements of this species. We highlight that both intrinsic and environmental drivers of animal movement should be integrated to better guide management strategies.

Environmental Hazards of Giant Reed (Arundo donax L.) in the Macaronesia Region and Its Characterisation as a Potential Source for the Production of Natural Fibre Composites.

This paper summarises the results obtained from the characterisation of giant reed (Arundo donax L.) plant and fibres. The research is part of a project developed in the Macaronesia region, of which the aim is to demonstrate the feasibility of using biomass from invasive plant species in the composites sector as a way of financing control campaigns and habitats conservation labours. An experimental procedure for the extraction of fibre bundles from this plant was developed, and the material obtained was characterised in terms of chemical composition, thermogravimetry and infrared spectra to evaluate its potential application in the production of polymeric composite materials as a strategy for the valorisation of residual biomass from this invasive species in Macaronesia. Thermoplastic matrix composites with fibre content up to 40 wt.% were produced and their mechanical properties under tensile, flexural and impact loading were determined. No references on the preparation of composite materials with polyolefin matrices and giant reed fibres have been found. Results obtained from mechanical tests show a good performance of the manufactured composites, with a significant increase in both flexural and tensile stiffness; the flexural modulus is almost tripled for PE-based composites and rises to 88% with respect to PP matrix. The ultimate flexural strength and the tensile and flexural yield strength are kept at acceptable values compared to neat polymer materials, although ultimate tensile strength and impact resistance are significantly affected when natural fibres are added.

Opuntia spp. Fibre Characterisation to Obtain Sustainable Materials in the Composites Field.

Some studies have evaluated the use of Opuntia as reinforcement for polymeric matrices, obtaining good results in energy absorption tests and increasing the tensile elastic modulus. However, no studies focusing on the previous characterisation of the fibres and their treatment to improve compatibility with polymeric matrices have been found. This work analyses the chemical composition of Opuntia maxima (OM) and Opuntia dillenii (OD) cladodes and fibre, studying how different treatments influence it. AOAC 2000 methods were used to determine non-structural components and the Van Soest method was used to estimate structural components. Surface characteristics of the samples were also evaluated by Fourier Transform Infrared Spectroscopy (FTIR). Opuntia fibre presented higher cellulose (50-66%) and lignin (6-14%) content and lower hemicellulose (8-13%) content than Opuntia cladodes (9-14% cellulose, 20-50% hemicellulose, 1-4% lignin). Despite the variability of lignocellulosic materials, OD cladodes treated with water and acetic acid achieved an increase in the structural components. Alkaline fibre treatment removed pectin and hemicellulose from the fibre surface, slightly increasing the cellulose content. Future research should evaluate whether the treated Opuntia fibre can improve the mechanical properties of reinforced polymer.

Valorization of Invasive Plants from Macaronesia as Filler Materials in the Production of Natural Fiber Composites by Rotational Molding.

This paper compares the mechanical properties of different natural fiber composites produced by rotational molding as a way of waste valorization from campaigns to control invasive plant species in Macaronesia. Rotomolded parts produced with polymeric matrices (polyethylene) and filled with up to 20% by weight of cellulosic fibers obtained from Arundo donax L., Pennisetum setaceum, and Ricinus communis plants were characterized in terms of tensile, flexural, and impact strength. It was found that the sieving of natural fibers allowed for their introduction in higher loadings, from 10 (for un-sieved material) to 20%; fiber size greatly affected the mechanical properties of the final parts, although some combinations were proven not to reduce the mechanical properties of the neat resin. This study is a first approach to the valorization of residues obtained from periodic campaigns of the control of invasive species performed by public authorities, usually at the local level. It is important to highlight that the main objective of this research did not focus on economically profitable activity; instead, it was focused on the reduction of wastes to be disposed from ecosystem maintenance actions and the investment of potential income into preservation policies.

Are Natural-Based Composites Sustainable?

This paper assesses the aspects related to sustainability of polymer composites, focusing on the two main components of a composite, the matrix and the reinforcement/filler. Most studies analyzed deals with the assessment of the composite performance, but not much attention has been paid to the life cycle assessment (LCA), biodegradation or recyclability of these materials, even in those papers containing the terms "sustainable" (or its derivate words), "green" or "eco". Many papers claim about the sustainable or renewable character of natural fiber composites, although, again, analysis about recyclability, biodegradation or carbon footprint determination of these materials have not been studied in detail. More studies focusing on the assessment of these composites are needed in order to clarify their potential environmental benefits when compared to other types of composites, which include compounds not obtained from biological resources. LCA methodology has only been applied to some case studies, finding enhanced environmental behavior for natural fiber composites when compared to synthetic ones, also showing the potential benefits of using recycled carbon or glass fibers. Biodegradable composites are considered of lesser interest to recyclable ones, as they allow for a higher profitability of the resources. Finally, it is interesting to highlight the enormous potential of waste as raw material for composite production, both for the matrix and the filler/reinforcement; these have two main benefits: no resources are used for their growth (in the case of biological materials), and fewer residues need to be disposed.

Cytocompatible cellulose nanofibers from invasive plant species Agave americana L. and Ricinus communis L.: a renewable green source of highly crystalline nanocellulose.

In this study, the fibers of invasive species Agave americana L. and Ricinus communis L. were successfully used for the first time as new sources to produce cytocompatible and highly crystalline cellulose nanofibers. Cellulose nanofibers were obtained by two methods, based on either alkaline or acid hydrolysis. The morphology, chemical composition, and crystallinity of the obtained materials were characterized by scanning electron microscopy (SEM) together with energy-dispersive X-ray spectroscopy (EDX), dynamic light scattering (DLS), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectroscopy. The crystallinity indexes (CIs) of the cellulose nanofibers extracted from A. americana and R. communis were very high (94.1% and 92.7%, respectively). Biological studies evaluating the cytotoxic effects of the prepared cellulose nanofibers on human embryonic kidney 293T (HEK293T) cells were also performed. The nanofibers obtained using the two different extraction methods were all shown to be cytocompatible in the concentration range assayed (i.e., 0|‒|500 µg/mL). Our results showed that the nanocellulose extracted from A. americana and R. communis fibers has high potential as a new renewable green source of highly crystalline cellulose-based cytocompatible nanomaterials for biomedical applications.

Assessment of the effect of autohydrolysis treatment in banana's pseudostem pulp.

Banana's pseudostem pulp (BPP) is a potential by-product obtained in the mechanical fiber extraction of banana's pseudostem. Its chemical characterization revealed to have an interesting composition, with a high polysaccharides content and low content in lignin, which makes it particularly relevant for the biorefinery's biochemical platform. Autohydrolysis pretreatment, studied under isothermal (140 °C) and non-isothermal conditions (140-220 °C), yielded oligosaccharides, mainly gluco-oligosaccharides, as the main soluble products. The highest oligosaccharides production (24 g/100 g raw material) was obtained at a severity factor of 2.3. Autohydrolysis pretreatment effectively disrupted the structure of the material, inducing an improvement of the enzymatic digestibility from 73% for the raw material up to 90% for the most severe conditions. Two stage autohydrolysis, with increasing severity, was also studied, allowing to obtain a higher amount of oligosaccharides (32 g/100 g raw material) and higher digestibility of the remaining solid (up to 97%).

Comparison between calcium carbonate and ß-tricalcium phosphate as additives of 3D printed scaffolds with polylactic acid matrix.

In this study, polylactic acid (PLA)-based composite scaffolds with calcium carbonate (CaCO3 ) and beta-tricalcium phosphate (ß-TCP) were obtained by 3D printing. These structures were evaluated as potential 3D structures for bone tissue regeneration. Morphological, mechanical, and biological tests were carried out in order to compare the effect of each additive (added in a concentration of 5% w/w) and the combination of both (2.5% w/w of each one), on the PLA matrix. The scaffolds manufactured had a mean pore size between 400-425 µm and a porosity value in the range of 50-60%. According to the results, both additives promoted an increase of the porosity, hydrophilicity, and surface roughness of the scaffolds, leading to a significant improvement of the metabolic activity of human osteoblastic osteosarcoma cells. The best results in terms of cell attachment after 7 days were obtained for the samples containing CaCO3 and ß-TCP particles due to the synergistic effect of both additives, which results in an increase in osteoconductivity and in a microporosity that favours cell adhesion. These scaffolds (PLA:CaCO3 :ß-TCP 95:2.5:2.5) have suitable properties to be further evaluated for bone tissue engineering applications.

Experimental Analysis and Simulation of Novel Technical Textile Reinforced Composite of Banana Fibre.

The use of natural fibres allows reducing environmental impact, due to their natural renewable origin and the lower energy needed for their production and processing. This work presents the mechanical characterization of a newly developed technical textile, with banana fibre treated by enzymes, comparing experimental results with numerical simulation based on the definition of the unit cell at micromechanical level. The experimental test shows that the composite with the fabric of banana fibre presents worse mechanical behaviour than the one with commercial flax fibre. The presence of wool, necessary for producing the yarn, reduces the mechanical properties of the banana textile. The numerical simulation had an acceptable error compared with the experimental results, with a global average error of 9%, showing that the predictive modelling based on the multiscale method is suitable for the design process of this kind of composite.

Three-dimensional printed polycaprolactone-microcrystalline cellulose scaffolds.

Microcrystalline cellulose (MCC) is proposed in this study as an additive in polycaprolactone (PCL) matrices to obtain three-dimensional (3D) printed scaffolds with improved mechanical and biological properties. Improving the mechanical behavior and the biological performance of polycaprolactone-based scaffolds allows to increase the potential of these structures for bone tissue engineering. Different groups of samples were evaluated in order to analyze the effect of the additive in the properties of the PCL matrix. The concentrations of MCC in the groups of samples were 0, 2, 5, and 10% (w/w). These combinations were subjected to a thermogravimetric analysis in order to evaluate the influence of the additive in the thermal properties of the composites. 3D printed scaffolds were manufactured with a commercial 3D printer based on fused deposition modelling. The operation conditions have been established in order to obtain scaffolds with a 0/90° pattern with pore sizes between 450 and 500 µm and porosity values between 50 and 60%. The mechanical properties of these structures were measured in the compression and flexural modes. The scaffolds containing 2 and 5% MCC have higher flexural and compression elastic modulus, although those containing 10% do not show this reinforcement effect. On the other hand, the proliferation of sheep bone marrow cells on the proposed scaffolds was evaluated over 8 days. The results show that the proliferation is significantly better (p < 0.05) on the group of samples containing 2% MCC. Therefore, these scaffolds (PCL:MCC 98:2) have suitable properties to be further evaluated for bone tissue engineering applications. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater 107B: 521-528, 2019.

Main factors affecting lacertid lizard thermal ecology.

The thermal ecology of ectotherms has been studied for almost 2 centuries, but additional attention is currently being paid to it, to understand how organisms deal with the environment in a climate change context. A consensus is still far away due to the large number of factors involved and their complex interactions. In this context, 3 analyses in lacertid lizards were carried out: (i) a meta-analysis, to test for differences between body and air temperatures from 71 populations; (ii) a meta-analysis concerning correlations between body and air temperatures from 60 populations; and (iii) a multimodel inference of thermoregulation effectiveness indices from 45 populations. The importance of different factors, including body size, habitat, insularity, altitude, climate and season, was evaluated in all analyses to model the response variables. A strong seasonality effect was observed, with a consistent pattern of less effective thermoregulation in summer compared to other seasons. Altitude was the second most important factor, with a consistent higher thermoregulation effort in populations occurring at high elevations (>1000 m above sea level). Other factors, such as insularity or body size, can also be important, but did not exhibit a clear pattern. Finally, thermoregulation was less affected by climate and habitat type.

Thermal ecology and microhabitat use of an arboreal lizard in two different Pantanal wetland phytophysionomies (Brazil).

Temperature is one of the main environmental variables shaping the evolution and biology of terrestrial ectotherms. The Pantanal is the largest continuous wetland in the World. However, a lack of knowlegde still exists on the thermal ecology of terrestrial ectothems from this wetland. In this context, the thermal ecology of the lizard Tropidurus lagunablanca Carvalho, 2016 (Squamata, Tropiduridae) was investigated in the Brazilian Pantanal. The thermal ecology and microhabitat use of lizards from a riparian forest was compared to lizards from a park savanna. At both studied areas, air and body temperatures of lizards did not differ between sexes. Mean T. lagunablanca body temperatures were higher at the savanna compared to the forest, while air temperatures were similar in both habitats. The main substrates were tree trunks, with a frequency of approximately 90% of the observations. Lizards from the savanna used higher perches than those from the forest despite -in average- trees were higher at the forest. Lizard sun and shade exposure was similar for both areas. Lizards from both habitats showed similar strong linear relationships between body and air temperatures. However, lizard behaviour of using tree trunk perches differently under different sunlight situations suggests that these lizards actively thermoregulate. Further research on the thermoregulation abilities of this species, with a null hypotesis and behavioral observations will shed light on lizard thermal biology. Studies on the ecophysiological aspects of these lizards should be a priority to understand how they will react to climate change and which conservation measures will be more effective concerning their preservation.